Permatex Guide97-2003

PRODUCT DESCRIPTION S.I.N.: 834-300 Permatex® Sensor-Safe Blue RTV Silicone Gasket is a single component, room temperature vulcanizing gasketing compound designed to provide reliable “formed-in-place” gaskets for mechanical assemblies. This material cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. The product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. The original “Blue” gasketing product, refined and oxygen sensor safe. OEM Specified. PRODUCT BENEFITS Superior adhesion and flexibility Sensor safe Replaces most cut gaskets Can be used as a gasket maker or dressing Easy application Non-flammable, Non-toxic TYPICAL APPLICATIONS Valve covers Timing gear covers Differential covers Oil pans Transmission pans Water pumps Thermostat housings For assembly as a gasket dressing 1. Repeat steps 1 thru 4 as in previous section. 2. Apply a thin film of silicone to one surface to be sealed. 3. Place the pre-cut gasket onto silicone film. 4. Apply a second thin to pre-cut gasket surface. 5. Remove any excess and assemble parts immediately. Note: Product not recommended for use as a cylinder head gasket or head gasket sealant. DIRECTIONS FOR USE For assembly as a form-in-place gasket 1. Remove all previous material from mating surfaces. PermatexGasket Remover is recommended for most PRODUCT DESCRIPTION S.I.N.: 834-300 PermatexUltra BlackGasket Maker is a single component, room temperature, vulcanizing, gasketing compound designed to provide reliable “formed-in-place” gaskets for mechanical assemblies. This material cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. The product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Designed to provide increased oil resistance and complies with extended warranty requirements. OEM Specified. PRODUCT BENEFITS Improved oil resistance Sensor safe, non-corrosive Good adhesion and flexibility Replaces most cut gaskets Can be used as a gasket maker or dressing Non-flammable, Non-toxic Low odor TYPICAL APPLICATIONS Oil pans Transmission pans Valve covers Valves and guides Timing gear covers Differential covers DIRECTIONS FOR USE For assembly as a form-in-place gasket 1. Remove all previous material from mating surfaces. Permatex® Gasket Remover is recommended for most materials, not for plastics or painted surfaces. 2. For best results, clean and dry all surfaces with a residue-free solvent, such as Permatex® Brake and Parts Cleaner 3. Cut nozzle to desired bead size, 1/16” to 1/4” in diameter. An 1/8” bead is usually sufficient for most applications. PRODUCT DESCRIPTION S.I.N.: 834-300 PermatexUltra GrayGasket Maker is a single component, room temperature vulcanizing gasketing compound designed to provide reliable “formed-in-place” gaskets for mechanical assemblies. This material cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. The product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Designed to perform under the higher load conditions of engines with closely spaced bolt patterns (typically non-US designed), and maintains outstanding oil, water-glycol resistance. OEM Specified. PRODUCT BENEFITS High load resistance Improved oil resistance Sensor safe, non-corrosive Replaces most cut gaskets Can be used as a gasket maker or dressing Non-flammable, Non-toxic Low odor TYPICAL APPLICATIONS Valve covers Transmission pans Oil pans Timing gear covers Differential covers DIRECTIONS FOR USE For assembly as a form-in-place gasket 1. Remove all previous material from mating surfaces. PermatexGasket Remover or Silicone Stripper is recommended for most materials. 2. For best results, clean and dry all surfaces with a residue-free solvent, such as PermatexBrake and Parts Cleaner. 3. Cut nozzle to desired bead size, 1/16“ to 1/4“ in diameter. A 1/8” bead is usually sufficient for most applications. 4. Remove cap, puncture tube or cartridge seal and attach extension nozzle. PRODUCT DESCRIPTION S.I.N.: 834-300 PermatexWater Pump & Thermostat RTV Silicone Gasket is a single component, room temperature vulcanizing gasketing compound designed to provide reliable “formed-in-place” gaskets for mechanical assemblies. This material cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. The product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Provides the highest water-glycol resistance available in an RTV silicone. PRODUCT BENEFITS Sensor safe, non-corrosive Superior adhesion and flexibility Easy application Replaces most cut gaskets Can be used as a gasket maker or dressing Non-flammable Non-toxic TYPICAL APPLICATIONS Thermostat housings Water pumps DIRECTIONS FOR USE For assembly as a form-in-place gasket 1. Remove all previous material from mating surfaces. PermatexGasket Remover is recommended for most materials, not for plastics or painted surfaces. 2. For best results, clean and dry all surfaces with a residue-free solvent, such as PermatexBrake and Parts Cleaner. 3. Cut nozzle to desired bead size, 1/16“ to 1/4“ in diameter. An 1/8” bead is usually sufficient for most applications. 4. Remove cap, puncture tube or cartridge seal and attach extension nozzle. 5. Apply a continuous and even bead of silicone to one surface, first tracing the internal areas of the gasket configuration, then all surrounding bolt holes as shown below: PRODUCT DESCRIPTION S.I.N.: 834-300 PermatexUltra Copperis a single component, room temperature vulcanizing gasketing compound designed to provide reliable “formed-in-place” gaskets for mechanical assemblies. This material cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. The product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Designed for the higher temperature environments encountered in 4-cylinder, turbocharged, and high performance engines. Permatex Ultra Copperis the most advanced high performance, high temperature (up to 700F intermittent) RTV gasket available. OEM Specified. PRODUCT BENEFITS High temperature resistance Sensor safe, non-corrosive Superior adhesion and flexibility Replaces most cut gaskets Improved oil resistance Can be used as a gasket maker or dressing Non-flammable, Non-toxic Low odor TYPICAL APPLICATIONS Exhaust manifolds Thermostat housings Valve covers Timing gear covers Water pumps Differential covers DIRECTIONS FOR USE For assembly as form-in-place gasket 1. Remove all previous material from mating surfaces. PermatexSilicone Stripper or Gasket Remover is recommended for most materials. 2. For best results, clean and dry all surfaces with a residue-free solvent, such as PermatexBrake and Parts Cleaner. 3. Cut nozzle to desired bead size, 1/16 “ to 1/4 “ in diameter. An 1/8” bead is usually sufficient for most applications. 4. Remove cap, puncture tube or cartridge seal and attach extension nozzle. 5. Apply a continuous and even bead of silicone to one surface, first tracing the internal areas of the gasket configuration, then all surrounding bolt holes as shown below: 6. Assemble parts immediately while silicone is still wet. Secure or tighten to recommended torque specs. 7. Re-torque will not be necessary after the product has cured. Instructions for PowerBead 1. Clean and dry all flange surfaces to be sealed. 2. Remove black cap from top of extension nozzle. 3. Turn nozzle extension one complete turn (360) counterclockwise. 4. Depress finger trigger and apply a continuous 1/16 inch to 1/8 inch PowerBeadto one surface. 5. Assemble parts immediately while silicone is still wet. 6. Finger tighten flange only until material begins to seep out the sides of the flange. 7. Allow to set for at least two hours and re-torque at least one quarter to one half turn. 8. For best results, allow to cure overnight. 9. To close, turn extension nozzle clockwise until tight (about one full turn). Wipe off excess material from nozzle and replace black cap. PRODUCT DESCRIPTION Permatex®High Temperature Anaerobic Flange Sealant is a high temperature sealant specifically engineered for making or dressing gaskets in rigid assemblies. It is able to withstand temperatures up to 400F (204C) and fills gaps up to 0.020 “ (primed) and permits clamping loads to be maintained for strong, leak-proof assemblies. PRODUCT BENEFITS Seals all surface imperfections Seals most common automotive fluids No cracking or shrinking during cure Eliminates costly retorquing operations Single component system Non-corrosive to metal parts TYPICAL APPLICATIONS Seals close fitting joints between rigid metal faces and flanges. Particularly suited where maximum temperature and chemical resistance is required. DIRECTIONS FOR USE 1. Surfaces to be sealed should be free of grease, oil and dirt. Use Permatex®Brake and Parts Cleaner to remove oil. Use Permatex®Gasket Remover to remove old gaskets. 2. Apply manually to one side of flange, making sure a continuous bead is applied. 3. Reassemble parts. Flanges should be tightened as soon as possible after assembly to avoid shimming. 4. Torque to normal specifications. 5. Parts may be returned to service in one hour. For Cleanup 1. Wipe off excess material with a clean cloth. 2. Clean hands with Permatex®Fast Orange® hand cleaner or soap and water. For Disassembly 1. For smaller assembled parts, heat part to 400F to 450F. 2. Use cautious, light prying or tapping motion to loosen the parts. Repeat heating/prying sequence as needed. 3. For larger assembled parts use prying/cleaving tools in combination with a light hammer and cautiously tap and pry the sides of the part to break the gasketed surfaces loose. 4. Once parts are disassembled, allow all surfaces to cool to room temperature. 5. Use Permatex®Gasket Remover to remove dried anaerobic material PHYSICAL PROPERTIES Typical Value Chemical Type Dimethacrylate Ester Appearance Gel Color Red Odor Acrid Specific Gravity 1.08 Viscosity cP Brookfield HBT TC @ 2.5 rpm @ 20 rpm 288,000 50,000 Gap cure (inch) 0.010 diametral ( Unprimed) 0.020 diametral (Primed) Cure Speed (Hours) 1 - 12 (Unprimed) 15 Minutes - 2 (Primed) Flash Point (F) >200 TYPICAL CURING PERFORMANCE Cure Speed vs. Substrate The rate of cure will depend on the substrate used. The graph below shows the shear strength developed with time on grit blasted steel lap shears compared to different materials and tested according to ASTM D 1002. Cure Speed vs. Activator Where cure speed is unacceptably long, or large gaps are present, applying activator to the surface will improve cure speed. The graph below shows the shear strength developed with time using Surface Prep Activator on grit blasted steel lap shears and tested according to ASTM D 1002. PRODUCT DESCRIPTION S.I.N.: 834-300 PermatexHigh Temperature Thread Sealant is a medium strength anaerobic sealant with PTFE for tapered pipe threads. This sealing compound is of a white, creamy paste consistency. The high lubricating properties of this compound prevents galling on pipe threads and fittings. It will provide immediate low pressure sealing and allow for the readjustment of fittings shortly after assembly. After 72 hours the joint is sealed to pipe burst pressure. This product has a medium solvent resistance and will withstand temperatures to 400F (204C). This product is not recommended for use on plastic piping. PRODUCT BENEFITS Resists leakage, vibration loosening, moisture, hydraulic fluids, diesel fuels. Lubricates threads for easy assembly and disassembly. Will not shred or wear like Teflontape. Parts may be repositioned for up to 24 hours after application. Suited for temperatures up to 400F (204C). TYPICAL APPLICATIONS Head bolts into through holes Oil PSI sending units/sensors Oil and coolant lines Fuel fittings Rear axle fill plug Brake and power steering fittings DIRECTIONS FOR USE 1. For best performance, surfaces should be clean and free of grease. 2. Product should be applied to the thread engagement area in sufficient quantity to fill all engaged threads. 3. Use accepted trade practices to assemble and wrenchtighten fittings until proper alignment is obtained. 4. Very large thread sizes may create large gaps, which will affect cure speed and strength. 5. For maximum pressure and solvent resistance, allow at PHYSICAL PROPERTIES OF UNCURED MATERIAL Typical Value Chemical Type Dimethacrylate ester Appearance White opaque paste Odor Acrid Specific Gravity 1.21 Viscosity (cP) 350,000 Flash Point (T.C.C.) F >200 Chemical resistance Gasoline, oil, water, glycol, hydraulic fluid, freon, transmission fluid, brake fluid PRODUCT DESCRIPTION S.I.N.: 834-300 PermatexHigh Performance Thread Sealant is formulated for fast, responsive curing on metal pipe threads and fittings. This sealant is a smooth, white paste-like compound with PTFE that controls lubricity to assist assembly and torque tightening. PermatexHigh Performance Thread Sealant replaces Teflon tape or pipe dopes. It cures rapidly to withstand 10,000 PSI within 24 hours. Prevents galling and protects mated threaded surfaces from rust and corrosion. The product cures when confined in the absence of air between close fitting metal surfaces. This product is not recommended for use on plastic piping. NSF White Book registered. PRODUCT BENEFITS Quick fixture time Prevents galling and corrosion Controlled strength Temperature and solvent resistance Immediate low pressure sealing Contains PTFE TYPICAL APPLICATIONS Stainless steel fittings Head bolts into through holes Oil PSI sending units/sensors Oil and coolant lines Hydraulic line fittings Brake fittings Transmission fluid fittings PTO fittings Air conditioning fittings DIRECTIONS FOR USE 1. For best performance, surfaces should be clean and free of grease. 2. Product should be applied to the thread engagement area in sufficient quantity to fill all engaged threads. 3. Use accepted trade practices to assemble and wrenchtighten fittings until proper alignment is obtained. 4. This product performs best in thin bond gaps. 5. Very large thread sizes may create large gaps, which will affect cure speed and strength. 6. For maximum pressure and solvent resistance, allow at least 24 hours for the product to fully cure before filling and pressurizing system. 7. This product is designed to give controlled friction (torque/tension ratio), during assembly. FOR CLEANUP 1. Wipe off any material outside the joint with a dry cloth. 2. Clean hands with PermatexFast Orange® hand cleaner or soap and water. 3. Cured material must be removed with PermatexGasket Remover. PHYSICAL PROPERTIES OF UNCURED MATERIAL Typical Value Chemical Type Methacrylate ester Appearance White opaque liquid Odor Acrid Specific Gravity 1.10 Viscosity (cP) 300,000 Flash Point (T.C.C.) F >200 Chemical resistance Gasoline, oil, water, glycol, hydraulic fluid, freon CURED INFORMATION (Cured 24 hours @ 75F) PRODUCT DESCRIPTION S.I.N.: 834-300 PermatexThread Sealant with Teflonis a smooth white paste with a slight alcohol odor. It is a fast acting paste/lubricant designed to seal pipes, fittings and threaded connections against leakage and loosening. Seals pressure to working rating of pipe in air, oil, gas and hydraulic systems. Lubricates threads for quick, easy assembly and disassembly. Prevents galling and corrosion. Will not tear or shred like tapes. Remains pliable through a wide temperature range and outperforms other pipe dopes. PRODUCT BENEFITS Easy to use Non drip formula Effective up to 5000 psi Good heat resistance Temperature range –65ºF to +300ºF(-54ºC to +204ºC) TYPICAL APPLICATIONS Air conditioning fittings Temperature sending fittings Hydraulic fittings DIRECTIONS FOR USE 1. Threads must be free of dirt and corrosion. 2. Apply to male threads. 3. Force sealant into the thread grooves with brush or spatula. 4. Assemble parts. 5. Adjustments can be made up to 24 hours after application without damage to seal. 6. Remove excess wet sealant by wiping with a dry cloth. Dried sealant can be peeled off. PROPERTIES OF UNCURED MATERIAL Typical Value Chemical Type Polymeric material Appearance White, smooth paste Odor Slight alcohol Specific Gravity @ 77ºF 1.12 Viscosity Paste Flash Point, TCC, ºF 74 GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). Ordering Information Part Number Container Size 80631 (14AR) 1 oz. tube, carded 80632 (14H) 4 oz. can 80633 (14D) 16 oz. can STORAGE Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8to 28C (46to 82F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. PRODUCT DESCRIPTION PERMATEXHigh Strength Threadlocker RED Gel is a high strength anaerobic threadlocking gel conveniently packaged in a new Gel Twistor Gel Squeezeapplicator. The product, like its liquid counterpart, is a single component, anaerobic gel that cures when confined in the absence of air between close fitting metal surfaces, ideal for all 3/8 inch to 1 inch (10mm to 25mm) and greater diameter threaded assemblies. Excellent chemical resistance and temperature resistance range of -65F to +300F (-54C to +149C). The assembly may require the use of heat to remove bolts. NSF Nonfood Components Program Listed (P1) (135870). PRODUCT BENEFITS Improved Reliability Eliminates vibration issues Seals against leakage Prevents rusting of threads Designed for use on vertical or hard-to-reach applications Cures without cracking or shrinking Adjusts or disassembles with hand tools Easy Application No mess Gel Twistor Gel Squeezeapplicator Gel-type product does not drip when applied Single component No curing outside of joint Thixotropic: resists dripping from threads during assembly No torque compensation required during assembly TYPICAL APPLICATIONS Prevents loosening and leakage of threaded fasteners. Particularly suitable for applications such as: Transmission shaft bolts Cylinder block Rocker arm studs Ring gear bolts Fan hub bolts DIRECTIONS FOR USE For assembly 1. Clean all threads (bolt and hole) with a cleaning solvent such as PermatexBrake and Parts Cleaner and allow to dry. 2. Remove the translucent protective cap by pulling off at an angle. 3. For Gel Twistturn the dial on the bottom of the container until 1/8” to 1/4" (3mm to 6mm ) of material protrudes from the top of the application tip. Note: First time use may require 4 to 5 full turns of the dial before material appears in the tip. For Gel Squeeze, remove cap and squeeze 1/8” to 1/4" (3mm to 6mm) of material beyond tip. 4. Apply threadlocker to the engagement area of the male fitting (usually the leading 5 to 6 threads). 5. Assemble parts and tighten to recommended torque. 6. If unused gel contacts metal threads, do not retract threadlocker back into the tube. Wipe off with a clean towel. 7. Replace protective cap. For Disassembly 1. Apply localized heat to nut or bolt to approximately 500F (260C). Disassemble while hot. Cure speed vs. temperature The rate of cure will depend on the ambient temperature. Full cure is attainable in 24 hours at room temperature, 72F (22C), or 1 hour at 200F (93C). PERFORMANCE OF CURED MATERIAL (After 24 hrs. at 72F on 3/8-16 steel Grade 8 Nuts and Grade 5 bolts) Typical Value Range Breakaway Torque, in.lbs 175 125 to 350 (Nm) (20) (14 to 40) Prevail Torque, ) (in.lbs) 230 200 to 350 PRODUCT DESCRIPTION PERMATEXMedium Strength Threadlocker BLUE Gel is a medium strength anaerobic threadlocking gel conveniently packaged in a new Gel Twistor Gel Squeezeapplicator. The product, like its liquid counterpart, is a single component, anaerobic gel that cures when confined in the absence of air between close fitting metal surfaces, ideal for all 6mm to 25mm (1/4 inch to 1 inch) diameter threaded assemblies. Excellent chemical resistance and temperature resistance range of -65F to +300F (-54C to +149C). The assembly is easily removable with hand tools for servicing requirements. NSF Nonfood Components Program Listed (P1) (135871). PRODUCT BENEFITS Improved Reliability Eliminates vibration issues Seals against leakage Prevents rusting of threads Designed for use on vertical or hard-to-reach applications Cures without cracking or shrinking Adjusts or disassembles with hand tools Easy Application No mess Gel Twistor Gel Squeezeapplicator Gel-type product does not drip when applied Single component No curing outside of joint Thixotropic: resists dripping from threads during assembly No torque compensation required during assembly TYPICAL APPLICATIONS Prevents loosening and leakage of threaded fasteners. Particularly suitable for applications such as: Belt tensioner bolts Pulley bolts Cup and core plugs Fan hub bolts Visor mount bolts Starter mounting bolts Alternator Mounting Bolts Intake Manifold Bolts DIRECTIONS FOR USE For assembly 1. Clean all threads (bolt and hole) with a cleaning solvent such as PermatexBrake and Parts Cleaner and allow to dry. 2. Remove the translucent protective cap by pulling off at an angle. 3. For Gel Twistturn the dial on the bottom of the container until 1/8” to 1/4" (3mm to 6mm) of material protrudes from the top of the application tip. Note: First time use may require 4 to 5 full turns of the dial before material appears in the tip. For Gel Squeeze, remove cap and squeeze 1/8 to 1/4" (3mm to 6mm) of material beyond tip. 4. Apply threadlocker to the engagement area of the male fitting (usually the leading 5 to 6 threads). 5. Assemble parts and tighten to recommended torque. 6. If unused gel contacts metal threads, do not retract threadlocker back into the tube. Wipe off with a clean towel. 7. Replace protective cap. . For Disassembly 1. Remove with standard hand tools. 2. In the rare instance where hand tools do not work, because of excessive engagement length, apply localized heat to nut or bolt to approximately 450F (232C). Disassemble while hot. TYPICAL CURING PERFORMANCE Cure speed vs. substrate The graph below shows the breakaway strength developed with time on 3/8” – 16 Grade 5 bolts and Grade 2 nuts for different materials. Cure speed vs. temperature The rate of cure will depend on the ambient temperature. Full cure is attainable in 24 hours at room temperature, 72F For Training Videos: Gasketing: http://www.permatex.com/videos/video_gasketing_eng.html Threadlocking: http://www.permatex.com/videos/video_threadlock_eng.html Note- Not an advertisement!!! For educational purposes Provided by acontour 1 Permatex® Sensor-Safe Blue RTV Silicone Gasket Maker The original Permatex Blue. Will not foul oxygen sensors. Replaces almost any cut gasket. Makes reliable “formed-in-place” gaskets that resist cracking, shrinking and migrating. Coats pre-cut gaskets to increase reliability. Temperature range -65°F to 500°F (-54°C to 260°C) intermittent; resists auto and shop fluids. First generation 1970-1980 gasket maker.Suggested Applications: Valve covers, oil pans, timing covers, water pumps, thermostat housings, transmission pans materials, not for plastics or painted surfaces. 2. For best results, clean and dry all surfaces with a residue-free solvent, such as PermatexBrake and Parts Cleaner. 3. Cut nozzle to desired bead size, 1/16“ to 1/4“ in diameter. A 1/8” bead is usually sufficient for most applications. 4. Remove cap, puncture tube or cartridge seal and attach extension nozzle. 5. Apply a continuous and even bead of silicone to one surface, first tracing the internal areas of the gasket configuration, then all surrounding bolt holes as shown below: 6. Assemble parts immediately while silicone is still wet. 7. Finger tighten flange only until material begins to seep out the sides of the flange. 8. Allow to set for at least two hours and re-torque at lease one quarter to one half turn. 9. For best results, allow to cure overnight. #80022 Permatex® Ultra Black® Maximum Oil Resistance RTV Silicone Gasket Maker OEM specified. For dealership warranty requirements, ensures extended drivetrain warranty compliance. Fast-curing formula. Sensor safe, low odor, noncorrosive. Meets performance specs of OE silicone gaskets. Retains high flexibility, oil resistance properties through use of a patented adhesion system. Temperature range -65ºF to 500ºF (-54°C to 260°C) intermittent; resists auto and shop fluids and vibration.Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, transmission pans 4. Remove cap, puncture tube or cartridge seal and attach extension nozzle. 5. Apply a continuous and even bead of silicone to one surface, first tracing the internal areas of the gasket configuration, then all surrounding bolt holes as shown below: 6. Assemble parts immediately while silicone is still wet. 7. Finger tighten flange only until material begins to seep out the sides of the flange. 8. Allow to set for at least two hours and re-torque at least one quarter to one half turn. 9. For best results, allow to cure overnight. For assembly as a gasket dressing 1. Repeat steps 1 through 4 as in previous section. 2. Apply a thin film of silicone to one surface to be sealed. 3. Place the pre-cut gasket onto silicone film. 4. Apply a second thin film to pre-cut gasket surface. 5. Remove any excess and assemble parts immediately. Note: Product is not recommended for use as a cylinder head gasket or head gasket sealant. #82180 Permatex® Ultra Grey® Rigid High-Torque RTV Silicone Gasket Maker OEM specified. Designed specially for high-torque and high vibration applications, like those common in import engines, this premium RTV gasket maker exceeds manufacturers' performance requirements. Noncorrosive and low-odor. Maximum vibration resistance, with outstanding resistance to oils, cooling and shop fluids. Guaranteed not to leak. Temperature range -65ºF to 500ºF (-54°C to 260°C) intermittent.Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, water pumps, thermostat housings below: 6. Assemble parts immediately while silicone is still wet. Secure or tighten to recommended torque specs. 7. Re-torque will not be necessary after the product has cured. For assembly as a gasket dressing 1. Repeat steps 1 through 4 as in previous section. 2. Apply a thin film of silicone to one surface to be sealed. 3. Place the pre-cut gasket onto silicone film. 4. Apply a second thin film to pre-cut gasket surface. 5. Remove any excess and assemble parts immediately. Note: Product is not recommended for use as a cylinder head gasket or head gasket sealant. #82194 Permatex® Water Pump & Thermostat RTV Silicone Gasket A noncorrosive, sensor-safe RTV silicone gasket material formulated specifically for water pumps and thermostat housings. Highest water-glycol resistance available in an RTV silicone. Temperature range of -65°F to 500°F (-54°C to 260°C) intermittent.Suggested Applications: Water pump and thermostat housings 6. Assemble parts immediately while silicone is still wet. 7. Secure or tighten to recommended torque specifications. Re-torque will not be necessary after the product has cured. For assembly as a gasket dressing 1. Repeat steps 1 thru 4 as in previous section. 2. Apply a thin film of silicone to one surface to be sealed. 3. Place the pre-cut gasket onto silicone film. 4. Apply a second thin to pre-cut gasket surface. 5. Remove any excess and assemble parts immediately. Note: Product not recommended for use as a cylinder head gasket or head gasket sealant. #22071 Permatex® Ultra Copper® Maximum Temperature RTV Silicone Gasket Maker OEM specified. Highest operating temperatures for 4-cylinder, turbocharged or high-performance engines. The most advanced, high temp RTV silicone gasket available. Sensor-safe, low odor, noncorrosive. Superior adhesion. Three times more oil resistant than conventional silicones; eight times more flexible than cut gaskets. Temperature range -75°F to 700°F (-59°C to 371°C) intermittent; resists auto and shop fluids and vibration. Suggested Applications: Exhaust manifolds/ headers, valve covers, oil pans, timing covers, water pumps, thermostat housings For assembly as gasket dressing 1. Repeat steps 1 thru 4 as in previous section. 2. Apply a thin film of silicone to one surface to be sealed. 3. Place the pre-cut gasket onto silicone film. 4. Apply a second thin to pre-cut gasket surface. 5. Remove any excess and assemble parts immediately. Note: Product not recommended for use as a cylinder head gasket or head gasket sealant. #81878 Permatex® High Temperature Anaerobic Flange Sealant A high temperature sealant specially engineered for making or dressing gaskets in rigid assemblies. Able to withstand temperatures to 400°F (204°C), fills gaps up to 0.020” (primed) and permits clamping loads to be maintained for strong, leakproof assemblies. Suggested Applications: Water pumps, thermostat housings, transmission pans, transmission case covers, transaxle casings, timing covers, and o-ring replacement #51031 Permatex® High Temperature Thread Sealant OEM specified. Locks and seals threaded fittings. Resists leakage, vibration loosening, moisture, hydraulic fluids and diesel fuels. Lubricates threads for easy assembly and disassembly. Won’t shred or wear like Teflon® tape. Parts may be repositioned up to 4 hours after application. Temperature range from -65°F to 400°F (-54°C to 204°C). Contains PTFE.Suggested Applications: Head bolts into through holes, oil PSI sending units and sensors, oil and coolant lines, fuel fittings, rear axle fill plug, brake and power steering fittings least 24 hours for the product to fully cure before filling and pressurizing system. 6. Fittings assembled with PermatexHigh Temperature Thread Sealant may be disassembled with normal hand tools. 7. For large pipe diameters (over 1"), heat may be required to disassemble fittings. 8. Fittings may be reused by removing loose sealant residue with a wire brush and reapplying sealant. CURED INFORMATION (Cured 72 hours @ 75F) Pressure Resistance (psi) 10,000 Temperature Range (F) -65 to +400 Breakaway torque (in.-lb.) 40 Maximum recommended pipe size 2" NPT #59214 GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Permatex® High Performance Thread Sealant OEM specified. Formulated specifically for metal, tapered pipe thread fittings, it replaces Teflon® tape and pipe dopes. Cures rapidly to withstand 10,000 PSI. Prevents galling and protects mated threaded areas from rust and corrosion. Contains PTFE. Suggested Applications: Stainless steel fittings, head bolts into through holes, oil PSI sending units/sensors, oil and coolant lines, intake manifold switches, rear axle fill plug, fuel fittings #56521 Pressure Resistance (psi) 10,000 Temperature Range (F) -65 to +300 Breakaway torque (in.-lb.) 40 GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). ORDERING INFORMATION Part Number Container Size 56521 50 ml. tube, carded STORAGE Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8C to 28C (46F to 82F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. Permatex® Thread Sealant with PTFE Economical general-purpose fitting sealant. Outperforms tapes and pipe dopes. Seals and resists pressure in air, oil, diesel fuel and hydraulic systems. Remains pliable at higher and lower temperatures. Temperature range -65°F to 300°F (-54°C to 149°C); resists common shop fluids.Suggested Applications: Air conditioning fittings, temperature sending fittings, hydraulic fittings #80631 NOTE The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. Permatex, Inc. specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Permatex, Inc. products and disclaims any liability for consequential or incidental damages of any kind, including lost profits. This product may be covered by one or more United States or foreign patents or patent applications. Permatex® GEL SQUEEZE™ High Strength Threadlocker RED Gel  Now available in a smaller 5 g applicator which puts the Threadlocker where you want it...on the part! Gel formula provides “liquid-reliability” without drips, globs, mess or waste. High strength threadlocker for heavy-duty applications. Especially well-suited for permanently locking studs and press fits. Adds 3,000 PSI holding power on slip and press fit assemblies. Replaces set screws and snap rings. Locks against vibration loosening. May require heat or special tools for removal. Suggested Applications: Cylinder block and rocker arm studs, ring gear bolts, frame bolts, shock absorber bolts; also ideal for vertical applications Shock absorber bolts Frame brackets Frame bolts Hydraulic press studs Suspension fasteners Large studs Heavy equipment bolts Gear bolts Railroad assemblies Construction equipment #27005 ORDERING INFORMATION Part Number Container Size 27010 10 gm Gel TwistApplicator, carded 27005 5 gm Gel SqueezeApplicator, carded (Nm) (26) (23 to 40) Where Breakaway Torque is the force required to initiate the fastener movement and Prevail Torque is the force required to disassemble the fastener once Breakaway Torque has occurred. TYPICAL ENVIRONMENTAL RESISTANCE Temperature Resistance Product temperature range from -65F to +300F (-54C to +149C). The breakaway and prevailing torque values decrease as temperature increases, however the assembly remains effective against vibration and leakage. Chemical / Solvent Resistance Aged under conditions and tested at 22C(72F) 3/8 – 16 steel nuts & bolts % Initial Strength retained after time Temp 500hr 1000hr Hot air 150C 41 Motor oil (SL) 125C 42 Antifreeze 87C 130 Gasoline RT 105 Ethanol RT 110 Acetone RT 135 GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). It is recommended to confirm compatibility of the product with such substrates. . . Permatex® GEL SQUEEZE™ Medium Strength Threadlocker BLUE Gel Now available in a smaller 5 g applicator which puts the Threadlocker where you want it...on the part! Gel formula provides “liquid-reliability” without drips, globs, mess or waste. All-purpose, medium strength threadlocker. Ideal for all nut and bolt applications 1/4 inch to 1 inch (6mm to 25mm). Eliminates need for stocking expensive lock nuts and lock washers. Locks and seals while preventing parts from loosening due to vibration. Protects threads from corrosion. Removable with hand tools for easy disassembly. Suggested Applications: Valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts, rocker arm adjustment nuts, carburetor studs; also ideal for vertical applications Valve Cover Bolts Vacuum Adjustment Screws Oil Pan Bolts Axle Cover Screws Drive Shaft Bolts Disc Brake Caliper Bolts Gearshift Knobs #24005 ORDERING INFORMATION Part Number Container Size 24010 10 gm Gel TwistApplicator, carded 24005 5 gm Gel SqueezeApplicator, carded Temp 1000hr Hot air 150C 47 Motor oil (SL) 125C 21 (22C), or 1 hour at 200F (93C). PERFORMANCE OF CURED MATERIAL (After 24 hrs. at 72F on 3/8-16 steel Grade 8 Nuts and Grade 5 bolts) Typical Value Range Breakaway Torque, in.lbs 115 70 to 150 (Nm) (13) (8 to 17) Prevail Torque, in.lbs 53 25 to 60 (Nm) (6) (3 to 7) Where Breakaway Torque is the force required to initiate the fastener movement and Prevail Torque is the force required to disassemble the fastener once Breakaway Torque has occurred. TYPICAL ENVIRONMENTAL RESISTANCE Temperature Resistance Product temperature range from -65F to +300F (-54C to +149C). The breakaway and prevailing torque values decrease as temperature increases, however the assembly remains effective against vibration and leakage. Chemical / Solvent Resistance Aged under conditions and tested at 72F (22C) 3/8 – 16 steel nuts & bolts % Initial Strength retained after time GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). It is recommended to confirm compatibility of the product with such substrates.